Description:
GENERAL
Print Technology: Thermal transfer and dot matrix
Material Type: Irradiated polyolefin heat shrink tubing (3:1 shrink ratio)
APPLICATIONS
Wire identification and insulation purposes
RECOMMENDED RIBBONS
Brady R5000 Series for dot matrix printing
Brady R4300 Series for thermal transfer printing
Brady R6600 Series for thermal transfer printing
Brady R4502S for thermal transfer printing silver on dark colored markers
Brady R6700 for thermal transfer printing white on dark colored markers
SPECIAL FEATURES
B-342 PermaSleeveTM Markers meet the material and physical property requirements of SAE AMS-DTL-23053/5C (class 1) for Insulation Sleeving and SAE AS-81531 for Marking of Electrical Insulating Materials when printed with R5000 Series dot matrix, R4300, R6600, R4502S, or R6700 Series thermal transfer ribbons.
B-342 is available in white, yellow, black, red, orange, green, blue, violet, pink, gray, and brown.
|
Details:
|
MARKER SIZE
|
RANGE OF WIRE DIAMETER (in)
|
RANGE OF WIRE DIAMETER (mm)
|
| 3/32" |
3PS-094 |
0.023 - 0.080
|
0.58 - 2.03
|
| 1/8" |
3PS-125 |
0.046 - 0.110
|
1.17 - 2.79
|
| 3/16" |
3PS-187 |
0.062 - 0.150
|
1.57 - 3.81
|
| 1/4" |
3PS-250 |
0.094 - 0.215
|
2.39 - 5.46
|
| 3/8" |
3PS-375 |
0.125 - 0.320
|
3.18 - 8.13
|
| 1/2" |
3PS-500 |
0.187 - 0.450
|
4.75 - 11.43
|
| 1" |
PS-1000 |
0.450 - 0.950
|
11.43 - 24.13
|
Shrink Method: Any industrial grade heat gun may be used to shrink B-342 PermaSleeve™ Markers.
B-342 white, yellow and other colors tested printed with R5000 Series dot matrix and R4300 and R6600 Series thermal transfer ribbons. B-342 black samples tested printed with R4502S silver and R6700 white thermal transfer ribbon. Results the same with all ribbons unless stated otherwise.
|
PERFORMANCE PROPERTIES
|
TEST METHODS
|
AVERAGE RESULTS
|
| High Service Temperatures |
5 minutes at 500°F (260°C)
24 hours at 350°F (180°C)
1000 hours at 267°F (130°C) |
Slight tubing discoloration.
Darkening on colors at 1000 hours.
Print legible with no visible effect to printing
|
| Low Service Temperature |
1000 hours at -40°F (-40°C) |
No visible effect |
| Weatherability |
ASTM G155 Cycle 1
1000 hours in Xenon Arc Weatherometer |
Slight discoloration (white), slight tubing fade (yellow, orange, blue, violet, pink), very slight print fade. Severe discoloration, slight print fade (red). Slight darkening (green, gray, brown). No visible effect to black marker |
| UV Light Resistance |
ASTM G155 Cycle 1 dry
1000 hours
|
Slight tubing discoloration (yellow, orange, green, blue, brown). Moderate tubing discoloration (red, grey, violet). Severe tubing discoloration (pink). No visible effect to black marker. |
| Humidity Resistance |
1000 hours at 100°F/95% R.H. |
No visible effect |
| Salt Fog |
1000 hours at 5% Salt Spray |
Moderate print fade (R4502S on black marker). No visible effect to all other color/ribbon combinations. |
| Dielectric Strength |
ASTM D2671 (after unrestricted shrink) |
500 volts/mil minimum |
| Flammability |
ASTM D2671, Procedure B |
Self-extinguishing within 60 seconds |
| Print Adherence per SAE-AS81531 (Sec 3.4.2) |
Samples tested after unrestricted shrink at 200°C for 3 minutes
20 eraser rubs with hard hand pressure
|
Print is still easily legible on sleeves printed with all ribbons. |
|
Solvent Resistance per SAE-AS81531 (Sec 3.4.3)
Solution A
Solution C
Solution D
|
Samples tested after unrestricted shrink at 200°C for 3 minutes
MIL-STD-202, Method 215K
3 cycles of 3 minute immersions in specified fluids followed by toothbrush rub after each immersion
|
Print still easily legible on sleeves printed with all ribbons in all three test fluids
|
Solution A: 1 part isopropyl alcohol, 3 parts mineral spirits
Solution B: deleted from MIL-STD-202, Method 215J
Solution C: BIOACT® EC-7R™ terpene defluxer
Solution D: 42 parts water, 1 part propylene glycol monomethyl ether, 1 part monoethanolamine at 70°C
|
PERFORMANCE PROPERTY
|
CHEMICAL RESISTANCE
|
B-342 white, yellow and other colors were dot matrix printed using Brady R5000 Series ribbon and shrunk on appropriate size wires. Test conducted at room temperature after 24 hour dwell. Testing consisted of 5 cycles of 10 minute immersions in the specified chemical reagent followed by 30 minute recovery periods. Samples rubbed with cotton swab after final immersion.
|
CHEMICAL REAGENT
|
SUBJECTIVE OBSERVATION OF VISUAL CHANGE
|
|
TUBING AND PRINTING WITHOUT SWAB RUB
|
PRINTING WITH SWAB RUB
|
| Methyl Ethyl Ketone |
No visible effect |
Slight print fade, print legible |
| Isopropyl Alcohol |
No visible effect |
Moderate print fade, print legible |
| JP-8 Jet Fuel |
No visible effect |
Slight print fade, print legible |
| Kerosene |
No visible effect |
Slight print fade, print legible |
| Mil 5606 Oil |
White and yellow tubing stained red on edges, no visible effect on printing |
Slight print fade, print legible |
| Mil 7808 Oil |
No visible effect |
Slight print fade, print legible |
| Speedi Kut Cutting Oil 332 |
No visible effect |
Slight print fade, print legible |
| Gasoline |
No visible effect |
Severe print fade, print just legible |
| Rust Veto® 377 |
Tubing stained orange, no visible effect on printing |
Slight print fade, print legible |
| Skydrol® 500B-4 |
No visible effect |
Moderate print fade, print legible |
| Propylene Glycol |
No visible effect |
No visible effect |
| Super Agitene® |
No visible effect |
Moderate print fade, print legible |
| BIOACT® EC-7R™ Terpene Cleaner |
No visible effect |
Severe print fade, print just legible |
| Deionized Water |
No visible effect |
No visible effect |
| 3% Alconox® Detergent |
No visible effect |
No visible effect |
| 5% Salt Water Solution |
No visible effect |
No visible effect |
B-342 white, yellow and other colors were thermal transfer printed using R4300 Series ribbon and shrunk on appropriate size wires. Test conducted at room temperature after 24 hour dwell. Testing consisted of 5 cycles of 10 minute immersions in the specified chemical reagent followed by 30 minute recovery periods. Samples rubbed with cotton swab after final immersion.
|
CHEMICAL REAGENT
|
SUBJECTIVE OBSERVATION OF VISUAL CHANGE
|
|
TUBING AND PRINTING WITHOUT SWAB RUB
|
PRINTING WITH SWAB RUB
|
| Methyl Ethyl Ketone |
No visible effect |
Slight print fade, print legible |
| Isopropyl Alcohol |
No visible effect |
Slight print fade, print legible |
| JP-8 Jet Fuel |
No visible effect |
Slight print fade, print legible |
| Kerosene |
No visible effect |
Slight print fade, print legible |
| Mil 5606 Oil |
Tubing stained red, no visible effect on printing |
Moderate print fade, print legible |
| Mil 7808 Oil |
No visible effect |
Moderate print fade, print legible |
| Speedi Kut Cutting Oil 332 |
No visible effect |
Slight print fade, print legible |
| Gasoline |
No visible effect |
Severe print fade, print just legible |
| Rust Veto® 377 |
Tubing stained orange, no visible effect on printing |
Slight print fade, print legible |
| Skydrol® 500B-4 |
No visible effect |
Slight print fade, print legible |
| Propylene Glycol |
No visible effect |
No visible effect |
| Super Agitene® |
No visible effect |
Slight print fade, print legible |
| BIOACT® EC-7R™ Terpene Cleaner |
No visible effect |
Severe print fade, print just legible |
| Deionized Water |
No visible effect |
No visible effect |
| 3% Alconox® Detergent |
No visible effect |
No visible effect |
| 5% Salt Water Solution |
No visible effect |
No visible effect |
B-342 white and yellow were thermal transfer printed using Brady R6600 Series ribbon and shrunk on appropriate size wires. Test conducted at room temperature after 24 hour dwell. Testing consisted of 5 cycles of 10 minute immersions in the specified chemical reagent followed by 30 minute recovery periods. Samples rubbed with cotton swab after final immersion.
|
CHEMICAL REAGENT
|
SUBJECTIVE OBSERVATION OF VISUAL CHANGE
|
|
TUBING AND PRINTING WITHOUT SWAB RUB
|
PRINTING WITH SWAB RUB
|
| Methyl Ethyl Ketone |
No visible effect |
Slight print fade, print legible |
| Isopropyl Alcohol |
No visible effect |
Slight print fade, print legible |
| JP-8 Jet Fuel |
No visible effect |
Slight print fade, print legible |
| Kerosene |
No visible effect |
Slight print fade, print legible |
| Mil 5606 Oil |
Tubing stained red on edges, no visible effect on printing |
Slight print fade, print legible |
| Mil 7808 Oil |
No visible effect |
Slight print fade, print legible |
| Speedi Kut Cutting Oil 332 |
No visible effect |
Slight print fade, print legible |
| Gasoline |
No visible effect |
Moderate print fade, print legible |
| Rust Veto® 377 |
Tubing stained orange, no visible effect on printing |
Slight print fade, print legible |
| Skydrol® 500B-4 |
No visible effect |
Slight print fade, print legible |
| Propylene Glycol |
No visible effect |
No visible effect |
| Super Agitene® |
No visible effect |
Moderate print fade, print legible |
| BIOACT® EC-7R™ Terpene Cleaner |
No visible effect |
Severe print fade, print just legible |
| Deionized Water |
No visible effect |
No visible effect |
| 3% Alconox® Detergent |
No visible effect |
No visible effect |
| 5% Salt Water Solution |
No visible effect |
No visible effect |
B-342 black samples were thermal transfer printed using R4502S silver ribbon and shrunk on appropriate size wires. Test conducted at room temperature after 24 hour dwell. Testing consisted of 5 cycles of 10 minute immersions in the specified chemical reagent followed by 30 minute recovery periods. Samples rubbed with cotton swab after final immersion.
|
CHEMICAL REAGENT
|
SUBJECTIVE OBSERVATION OF VISUAL CHANGE
|
|
TUBING AND PRINTING WITHOUT SWAB RUB
|
PRINTING WITH SWAB RUB
|
| Methyl Ethyl Ketone |
No visible effect |
Slight print fade |
| Isopropyl Alcohol |
No visible effect |
No visible effect |
| JP-8 Jet Fuel |
No visible effect |
Moderate print fade, print legible |
| Kerosene |
No visible effect |
Slight print fade |
| Mil 5606 Oil |
No visible effect |
Moderate print fade, print legible |
| Mil 7808 Oil |
No visible effect |
Slight print fade |
| Speedi Kut Cutting Oil 332 |
No visible effect |
Slight print fade |
| Gasoline |
No visible effect |
Slight print fade |
| Rust Veto® 377 |
No visible effect |
Slight print fade |
| Skydrol® 500B-4 |
No visible effect |
Slight print fade |
| Propylene Glycol |
No visible effect |
Slight print fade |
| Super Agitene® |
No visible effect |
Moderate print fade, print legible |
| BIOACT® EC-7R™ Terpene Cleaner |
No visible effect |
Slight print fade |
| Deionized Water |
No visible effect |
No visible effect |
| 3% Alconox® Detergent |
No visible effect |
No visible effect |
| 5% Salt Water Solution |
No visible effect |
No visible effect |
B-342 black samples were thermal transfer printed using R6700 white ribbon and shrunk on appropriate size wires. Test conducted at room temperature after 24 hour dwell. Testing consisted of 5 cycles of 10 minute immersions in the specified chemical reagent followed by 30 minute recovery periods. Samples rubbed with cotton swab after final immersion.
|
CHEMICAL REAGENT
|
SUBJECTIVE OBSERVATION OF VISUAL CHANGE
|
|
TUBING AND PRINTING WITHOUT SWAB RUB
|
PRINTING WITH SWAB RUB
|
| Methyl Ethyl Ketone |
No visible effect |
Slight print fade |
| Isopropyl Alcohol |
No visible effect |
Slight print fade |
| JP-8 Jet Fuel |
No visible effect |
Moderate print fade, print legible |
| Kerosene |
No visible effect |
Moderate print fade, print legible |
| Mil 5606 Oil |
No visible effect |
Moderate print fade, print legible |
| Mil 7808 Oil |
No visible effect |
Slight print fade |
| Speedi Kut Cutting Oil 332 |
No visible effect |
Slight print fade |
| Gasoline |
No visible effect |
Moderate print fade, print legible |
| Rust Veto® 377 |
No visible effect |
Slight print fade |
| Skydrol® 500B-4 |
No visible effect |
Slight print fade |
| Propylene Glycol |
No visible effect |
No visible effect |
| Super Agitene® |
No visible effect |
Moderate print fade, print legible |
| BIOACT® EC-7R™ Terpene Cleaner |
No visible effect |
Moderate print fade, print legible |
| Deionized Water |
No visible effect |
No visible effect |
| 3% Alconox® Detergent |
No visible effect |
No visible effect |
| 5% Salt Water Solution |
No visible effect |
No visible effect |
Product testing, customer feedback, and history of similar products, support a customer performance expectation of at least five years from the date of receipt for this product as long as this product is stored in its original packaging in an environment at 65-95 degrees F per SAE AMS-23053/5C. We are confident that our product will perform well beyond this time frame. However, it remains the responsibility of the user to assess the risk of using such product. We encourage customers to develop functional testing protocols that will qualify a product's fitness for use, in their actual applications.
|
